Hello.
Raspi B rev.2; Swap=512M; 8GB SD; Fresh installed Raspbian Stretch

$./setup.sh
#install process and and at the end
<code>
lazarus/components/lazsvnpkg/languages/svnclasses.hu.po lazarus/components/lazsvnpkg/languages/svnclasses.lt.po lazarus/components/lazsvnpkg/languages/svnclasses.it.po lazarus/components/lazsvnpkg/Makefile
lazarus/components/lazsvnpkg/lazsvnpkg.lpk
lazarus/components/lazsvnpkg/lazsvnpkg_images_list.txt lazarus/localize.bat
lazarus/lazarus
An unhandled exception occurred at $000128B0:
EAccessViolation: Access violation
$000128B0

Your Free Pascal 3.3.1 with Lazarus 2.0 is now installed </code>

When I am Trying to start Lazarus:
$ ./lazarus.sh
<code>
An unhandled exception occurred at $000128B0:
EAccessViolation: Access violation
$000128B0

An unhandled exception occurred at $000267D0:
EAccessViolation: Access violation
$000267D0
</code>

Does anybody know what I am doing wrong?
Thank You, Milan.

An 8GB SD-card for an RPi Stretch does not give you much leeway! Better to use a 32 GB SDcard!
You want to have space for the fpc/lazarus sources and the make install may even duplicate these. They are easily multi GB in size.

And I would set swap to 1024M because the build process on an RPi is pretty disk intensive. 512M is on the low (too low?) side.

I have 2 GB free space with Lazarus installed.
I think it was not swap problem.
Thx

Dňa 21. 3. 2019 o 8:49 Bo Berglund via lazarus napísal(a):

Milan Baša wrote

I have 2 GB free space with Lazarus installed. I think it was not swap problem.

On my Rpi3 with Stretch I have the following sizes: ~/dev/fpc/3.0.4 =581 M
~/dev/fpc/laz/2.0.0 = 959 M
~/share/src/fpc-3.0.4 = 287 M
Just these are a total of 1827 M

I build both from sources via svn in my user home dir.

My experience is that when the fpc or lazarus build process stop with strange errors then swap size is the culprit.
I always use 1 GB swap. But that of course needs an additional 1 GB of disk space so with an 8GB SD-card you need 2.83 GB for fpc/laz and are left with about 5 GB for operating system and everything else....

I still say you should go for a larger SD card and set swap higher.

You could check how much you have used in a dir tree:

du -sh <target dir>
Ex:
$ du -sh ~/dev/fpc/3.0.4
581M /home/pi/dev/fpc/3.0.4

Or for total summary of the free space on the disk:

$ sudo du -sh /
17G     /

OK. Thank You. I will buy larger SD. This one is what I I will try new card. Thank you for the effort.

Dňa 21. 3. 2019 o 10:30 Bo Berglund via lazarus napísal(a):

Milan Baša wrote

OK. Thank You. I will buy larger SD. This one is what I have at home. Tomorrow I will try new card. Thank you for the effort.

Ik Lazarus crashes (Access violation) immediately on startup this has probably nothing to do with the size of your SD. It might be favourable to update it anyways, but won't solve your problem.

Did you compile Lazarus yourself? Or downloaded it somewhere? Better check that you have the correct version.

Regards,

Joost

Downloaded from Walters page, tryied two times. I bought 16GB and now I am updating Stretch. I will send a message. Thx

Dňa 22. 3. 2019 o 13:20 Joost van der Sluis via lazarus napísal(a):

SD: 16GB, Swap: 1G
After fresh install the same problem.

Dňa 22. 3. 2019 o 13:20 Joost van der Sluis via lazarus napísal(a):

Op 22-03-19 om 15:38 schreef Milan Baša via lazarus:

Downloaded from Walters page, tryied two times. I bought 16GB and now I am updating Stretch. I will send a message. Thx

I know nothing about Walter's page. But you need a Lazarus version that is compiled for exactly your system. (Processor, libraries and such)

Why don't you compile Lazarus yourself? (make build)

I would also check first if fpc works at all. (fpc -h)

You could also try to run Lazarus in the debugger:

gdb ./lazarus
run

Regards,

Joost.

Milan Baša wrote

SD: 16GB, Swap: 1G After fresh install the same problem.

Are you building Lazarus and fpc yourself on the RPi platform??? If not then you should.

https://www.getlazarus.org/setup/?download#linux

pi at raspberrypi:~/Development/FreePascal/fpc/bin $ /home/pi/Development/FreePascal/fpc/bin/fpc -h
An unhandled exception occurred at $0007CC60:
EAccessViolation: Access violation
$0007CC60
$0004ABB8
$00044214

Error: /home/pi/Development/FreePascal/fpc/bin/ppcarm returned an error exitcode

pi at raspberrypi:~/Development/FreePascal/lazarus $ gdb ./lazarus GNU gdb (Raspbian 7.12-6) 7.12.0.20161007-git
Copyright (C) 2016 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later
<http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. Type "show copying" and "show warranty" for details.
This GDB was configured as "arm-linux-gnueabihf".
Type "show configuration" for configuration details. For bug reporting instructions, please see:
<http://www.gnu.org/software/gdb/bugs/>.
Find the GDB manual and other documentation resources online at: <http://www.gnu.org/software/gdb/documentation/>.
For help, type "help".
Type "apropos word" to search for commands related to "word"... Reading symbols from ./lazarus...(no debugging symbols found)...done. (gdb) run
Starting program: /home/pi/Development/FreePascal/lazarus/lazarus [Thread debugging using libthread_db enabled]
Using host libthread_db library
"/lib/arm-linux-gnueabihf/libthread_db.so.1".

Program received signal SIGILL, Illegal instruction. 0x000267d0 in ?? ()
(gdb)

OK I will try to build it myself.
Thank You.

Dňa 22. 3. 2019 o 21:20 Joost van der Sluis via lazarus napísal(a):